Monport 60W JPT MOPA Fiber Laser vs xTool F1 Dual-Laser Engraver (2W IR + 10W Diode)
Head-to-head spec comparison to help you pick the right fiber laser for your needs.
Monport
$899
xTool
$799
Spec-by-Spec Comparison
| Spec | Monport 60W JPT MOPA Fiber Laser | xTool F1 Dual-Laser Engraver (2W IR + 10W Diode) |
|---|---|---|
| Wattage | 60 W | 2 W |
| Laser Type | MOPA | IR Diode (not fiber galvo) |
| Laser Source | JPT | xTool IR |
| Work Area (W) | 175 mm | 110 mm |
| Work Area (H) | 175 mm | 110 mm |
| Galvo Speed | 8000 mm/s | 4000 mm/s |
| Color Marking | Yes | No |
| LightBurn | Yes | Yes |
| Autofocus | No | No |
| Weight | 5 kg | 2.5 kg |
| Software | BSLcad + LightBurn (galvo license required separately) | xTool Creative Space + LightBurn |
| Pulse Width | 2–500ns | N/A |
| Price | $899 | $799 |
| Rating | 7.5/10 | 7.9/10 |
| Buy on Amazon | Buy on Amazon |
Pros & Cons
Monport 60W JPT MOPA Fiber Laser
Pros
- 60W JPT MOPA at $899 undercuts the ComMarker B4 60W MOPA by $200 with a matching 175×175mm work area and rotary axis included in the box
- 175×175mm work area confirmed on the Amazon listing — accommodates full-size tumblers with a rotary chuck without lens swaps
- LightBurn galvo support confirmed via BSLcad controller — Amazon listing explicitly states 'All Monport fiber marking machines can be operated using Lightburn'
- 1–4,000kHz frequency range and 2–500ns pulse width provide the full MOPA parameter envelope for stainless steel color marking and titanium anodization
- 60W output is meaningfully faster than 30W for deep engraving — depth-map coin engraving documented by a Reddit owner using LightBurn 3D slice at production-viable speeds
Cons
- Only 16 Amazon ratings — too thin to verify factory QC or catch edge-case failures; at this wattage, a single DOA unit would represent 6% of all reviews
- No community material libraries for BSLcad exist anywhere — owners building color marking settings start from zero; the LightBurn parameter libraries that circulate for OMG Laser and ComMarker do not transfer
- In buyer comparison threads for 60W MOPA, Monport was explicitly excluded from recommendations due to 'unclear specs, lack of real user feedback' — OMG Laser and Haotian dominate those conversations
- MOPA settings complexity is brand-documented as brutal for newcomers — one Reddit owner described the transition from CO2 as 'feeling like I've never used technology before' with their Monport MOPA
- 60W is a Class 4 open-beam laser — no enclosure, invisible 1064nm infrared beam, requires OD5+ eyewear and a dedicated controlled workspace; not a beginner purchase at any price
xTool F1 Dual-Laser Engraver (2W IR + 10W Diode)
Pros
- Two machines in one enclosure: 2W IR marks metal (steel, aluminum, brass), 10W diode cuts wood, leather, and acrylic — single $799 machine that eliminates owning both a fiber and a diode laser
- xTool Creative Space software is the most polished beginner interface in the laser category — camera positioning, guided material presets, and auto-layout workflows available from day one
- Fully enclosed with automatic safety shutoffs — the only machine in this tier safe to operate in an office, living room, or classroom without OD5+ eyewear and ventilation setup
- LightBurn compatible for users who want full parameter control beyond what xTool's software exposes
- xTool has the largest installed base and most active community of any Chinese laser brand — tutorial content, settings libraries, and troubleshooting threads for every use case are indexed and searchable
Cons
- 2W IR laser is NOT a fiber galvo — it produces lighter, less consistent marks on hard metal than a dedicated 20W fiber laser; an owner who ran both side by side measured the fiber as '25x faster on average for marking metal'
- IR laser head is the documented primary failure point — multiple owners report the IR head degrading or dying within 1–2 years of regular use; xTool support unable to repair in some markets
- No autofocus — autofocus is exclusive to the F1 Ultra; this model requires manual two-dot alignment each session (a common point of confusion because the F1 Ultra, a completely different machine, has autofocus)
- 110×110mm work area matches budget dedicated fiber lasers — tumblers require a rotary and repositioning, no advantage here over GWEIKE or ComMarker alternatives
- At $799 you are paying for the dual-laser concept and xTool brand polish, not metal marking throughput — a dedicated 30W fiber laser at the same price marks stainless 10–25x faster
Our Verdicts
Monport 60W JPT MOPA Fiber Laser
The Monport 60W MOPA is worth considering if you want the highest wattage color-marking machine under $1,000 and you have enough MOPA experience to build settings from scratch without community support. With only 16 Amazon reviews and near-zero BSLcad community resources, you are working without a safety net. The ComMarker B4 60W MOPA at $1,099 has documented settings, active LightBurn forum threads, and a track record — the $200 premium buys real support infrastructure. For experienced MOPA operators who know what they are doing, the Monport is a defensible value. For everyone else, pay the $200 and get the ComMarker.
xTool F1 Dual-Laser Engraver (2W IR + 10W Diode)
The xTool F1 is worth buying if and only if you genuinely need both metal marking and non-metal work (wood, acrylic, leather) in a single safe, enclosed desktop machine. That value proposition is real and has no direct competitor. If your work is metal-only, the GWEIKE G2 Pro at the same $799 price marks stainless 10–25x faster with better depth. Two critical clarifications: the F1 original uses a 2W IR diode laser, not a fiber galvo, and has no autofocus — both of those features belong to the F1 Ultra, which is a completely different machine at a higher price. Compare them only if you understand the difference.